چوب Poison Arsenic-3 5

توضیحات

Product ID: PO3AR5

Cue Type: Play Cue

Shaft Type: Poison Venom 2

Put some bite into your game. No low-deflection shaft in its class comes close to the Venom2 shaft that tops-off every Poison playing cue. Designed with the Predator Groups exclusive Double Density (DD) TechnologyTM and backed by Predator’s proven performance engineering, it’s the equivalent of making the pockets wider and your opponent’s eyes bigger.

Joint Type: Uni-Loc Bullet

Cue Tip: Poison Sarin Tip

Shaft Diameter: 13mm

Shaft Length: 29 Inch

Shaft Taper: Pro Taper

The pro taper is more comon on most cues today. A pro tapered shaft starts at the ferrule and keeps the same diameter 12 to 14 inches up the shaft before starting to get larger toward the shaft joint. This keeps a consistent size of shaft when back and forth in your bridge hand.

Joint Collar: Stainless

Wood Type: Maple – Curly

Care & Instructions: Instructions

Poison CARE INSTRUCTIONS

WARPAGE – FINISH. Wood will soak up moisture in wet climates and release moisture in dry climates. To prevent warpage or finish problems, store your cue in an environment that has a stable and consistent temperature with a humidity level of 40 to 45 percent.

ABUSE. Cues made of wood are not designed to withstand lateral pressure and should not be leaned or propped up against a wall, dropped on the floor, bent excessively while playing, or hit on a table. We recommend protecting your cue with a case.

TIP DIAMETER. We do not recommend turning your shaft down. You can choose to turn your shaft, but any Poison shaft turned below 12.25 mm will result in an automatic void of your warranty.

PHENOLIC TIP REPLACEMENT. If you want to replace your phenolic tip on you Poison break cue or your Poison jump cue, do not remove the black carbon fiber tip plate located under the brown phenolic tip as this will reduce the strength of your shaft and void the warranty. Leave .020″ of the brown phenolic before gluing on the replacement tip.

SHAFT MAINTENANCE. To clean your Poison shaft, use a towel slightly dampened with rubbing alcohol. After cleaning, use a leather burnisher or similar material to seal the shaft. Using a Carnuba wax may also help to seal the shaft and protect it from moisture. To avoid damage, do not sand the shaft; no abrasive is necessary. Do not expose the shaft to excessive moisture and do not steam it to remove dings. Importantly, do not use any water-based cleaner.

UNI-LOC® JOINT. We recommend cleaning the Uni-Loc® joint when you first receive your cue and every six months thereafter. These joints are precision manufactured to exact tolerances and even a modest amount of dirt can create a problem. You can use a Q-Tip dipped in Isopropyl alcohol to clean the inside threads and bore of the shaft insert. Clean the joint pin and threads with alcohol and a clean rag. We recommend the use of joint protectors to help keep your joint clean and to protect it from damage.

FERRULE. Much of the shaft’s performance can be attributed to our ferrule design and composition. Due to the performance enhancing material used for the ferrule, scratches may appear with normal use. In this case, we recommend sending your shaft to an authorized Poison repair center for a clean up. Removing or changing the ferrule will void the warranty.

TIP. The Sarin® tip comes standard on all Poison playing shafts. If a tip replacement is needed, we recommend a medium-hard tip. For best results, we recommend that you send it to an authorized Poison repair center for installation of a new tip.

WRAP CLEANING. For grips and wraps, barely dampen a towel with water, wipe the wrap, and dry it immediately. Use Isopropyl alcohol for Irish Linen wraps.

Warranty: Limited Lifetime

دیدگاهها

هیچ دیدگاهی برای این محصول نوشته نشده است.

اولین نفری باشید که دیدگاهی را ارسال می کنید برای “چوب Poison Arsenic-3 5”